HOLIDAY SPECIAL: A free Limited Edition Trow & Holden T-shirt will be included with every Tool Set or tool purchase more than $375!

 

Air Compressor Buying Guide

 

With a seemingly endless variety of air-powered tools manufactured for everything from home craft projects to industrial stone fabrication, pneumatic tool requirements and compressor configurations can range widely. If you are considering the purchase of a Trow & Holden pneumatic hammer, there are a few things to keep in mind to ensure you have an adequate source of compressed air to power your tool.

Choosing the air compressor that is right for you is really a matter of how it will be used, budget, and personal preference. While this document is intended to help you find an air compressor best suited for your needs, don’t forget to keep in mind the nature of your work and any limiting factors, such as access to electricity, ventilation, portability, and noise.

 

Air Compressor Basics

There are three primary specifications to keep in mind when shopping for an air compressor.

Air Supply

Trow & Holden pneumatic tools require an air flow of approximately 3–8 CFM (cubic feet per minute) at 90–100 psi (pounds per square inch), which will vary based on the size of your air tool. You will want to make sure the compressor’s output and duty cycle will allow you to take advantage of your air tool’s full range of power. Remember, too much air cannot damage your Trow & Holden pneumatic hammer.

Tank Size

Another important consideration is the compressor’s tank size. Trow & Holden pneumatic hammers run on a constant flow of air — unlike more common air-powered tools, which only require frequent bursts of air. This means your Trow & Holden air hammer will deplete its air supply quickly. We generally recommend a compressor with at least 20 gallons of air storage capacity.

Compressor Configuration

Lastly, think about whether or not you want to use compressed air to power other types of air tools, such as grinders, drills or polishers. Running multiple tools at the same time can significantly increase the amount of air needed to power your tools. When possible, consider two-stage compressors, which are most appropriate for powering pneumatic tools with high air consumption.

 

Features That Make A Difference

 

Air Compressor Specifications

All pneumatic tools will require a certain air flow and pressure for optimal performance. While it is important that your compressor’s output meets these specifications, you should also have an understanding of how these basic measurements and compressor features are related:

PSI (Pounds per Square Inch)

This is the measure of air pressure delivered by your compressor. The higher the psi, the further the air can be compressed meaning a larger volume of compressed air can be stored in the tank.

CFM (Cubic Feet per Minute)

This is the volume of air that your compressor can pump in one minute at a specific working pressure. High CFM ratings mean a compressor can provide more air, making higher CFM units more practical for larger applications.

HP (Horsepower)

This is the unit of measurement for the power your compressors motor produces. Higher horsepower engines produce greater psi and are capable of carrying a heavier workload. This can be particularly important if your need for portability limits your compressors tank size.

Tank Size

Compressors with larger tanks (measured in gallons) can supply more air to your tools between duty cycles, which will put less strain on your compressor’s motor and pump. Smaller tanks will increase portability, but output and duty cycle rates should be considered carefully.

To choose a compressor that will meet the requirements for your tools to function properly, use this formula. Select the tool that requires the highest CFM at the highest psi. Then add 50% to the required CFM as a safety margin. For example, if a tool requires 3 CFM at 90 psi, choose a compressor that provides at a minimum 4.5 CFM at 90 psi.

Once you know the volume and pressure requirements you need, your choices can be considered between these main configurations:

 

Visit Your Local Dealer

A great resource for finding the right unit is your local power equipment dealer. Remember that an air compressor should be able to safely power all the tools you plan on using, so bring along a list of those tools and their air specifications to share with the dealer. Be sure to start the unit and try the controls. Ask the dealer if he or she has a model that can be test-driven on-site or at home before making a final buying decision.

 

 

Subscribe to our newsletter